Products

Short rear floor brace for hardtops and convertibles.

Please select side below

Reproduction floor brace, located under front seat area and extends from rocker panel to rocker panel. American made. 

End section of brace where it attaches to the rocker.

AMERICAN MADE

Please select side below

Complete front floor brace, convertible models only. 

Trunk body mount brace. Welds to trunk floor above rear axle area. Fits convertible models only. 

Reproduction floor brace, located under front leg of front seat, attaches to floor and rocker panel. Fits left or right side.

USA MADE

Sheet metal brace welds to bottom of floor under front seat. Made in USA.
Please select side below.

Reproduction floor brace. American made. Located under floor where toe board and front floor meet at the base of the firewall.
Please select side below.

Repair section for lower firewall.
 Made in the USA. Please select side below

This is a 1955-57 kick panel retainer. The retainer holds the lower edges of the kick panels. Welded next to the toe boards. Sold single. Will fit left or right side. 

Dimmer switch mounts to this plate and then mounts to floor board. A lot of times is missing or rotted.

Reproduction 1-pc toe board for 1955-56 Chevrolet's. Fits complete width between kick panels. 

Reproduction 1-piece toe board for 1957 Chevrolet's. Fits complete width between kick panels.

Front floor pan section. Fits all models.

Please select side below.

Replacement firewall for 1955-56 Chevrolet's. Has all original factory holes. Fits all 150,210 or Belair models.

NOTE: This item ships truck freight only. We will quote shipping charges prior to delivery.

Replacement smooth style firewall for 1955-56 Chevrolet's. Stamped with original reinforcement ribs and braces, but without any factory holes. Eliminates the need to weld up unwanted holes when building a custom car. Installs in factory location. Finished in a weld through primer.

NOTE: This item ships truck freight. You will be notified of shipping charges prior to shipment being made.

Replacement firewall for 1957 Chevrolet's. Fits all 150,210 or Belair models. Includes all factory holes.

NOTE: This item ships truck freight only. We will quote shipping charges prior to delivery.

Replacement smooth style firewall for 1957 Chevrolet's. Stamped with original reinforcement ribs and braces, but without any factory holes. Eliminates the need to weld up unwanted holes when building a custom car. Installs in factory location. Finished in a weld through primer.

NOTE: This item ships truck freight. You will be notified of shipping charges prior to shipment being made.

These plates are used to block off the fresh air duct holes in the firewall of a 1957 Chevrolet when eliminating the stock inner fender fresh air ducts. Made in 18 ga. steel and come powder coated black. Attaches with original screws. Sold as a pair.

This kit eliminates the large inner fender air ducts on a 1957 Chevrolet and allows to convert to cold air induction. Headlight panels allow for the proper headlight bucket mounting. Kit includes block-off plates for firewall and headlight bucket mount panels. One panel includes a 4" cold air induction tube which can be used in LS conversions or any other cold air induction systems. This can be mounted either on the left or right side. Made in 18 gauge. black powder coated steel. Mounts using all original hardware.

This kit eliminates the large inner fender air ducts on a 1957 Chevrolet and allows to convert to cold air induction. Headlight panels allow for the proper headlight bucket mounting. Kit includes block-off plates for firewall and headlight bucket mount panels. Headlight panels include a 4" cold air induction tubes which can be used in LS engine conversions or any system using cold air induction. Made in 18 ga. black powder coated steel. Mounts using all original hardware.

This kit allows the elimination of the factory inner fender air ducts in a 1957 Chevrolet and still be able to mount the headlight bucket properly. This installation is typical in a car where the firewall has been modified or modern AC systems are installed and the ducts are no longer necessary. Made in 18 ga. black powder coated steel. Attaches with all stock hardware. Kit includes headlight panel only.

Replacement sheet metal panel for repairing the floor tunnel in the transmission area.